Not Helpful 2 Helpful The wires are not grounded properly, check to make sure the surface is clean, unpainted metal. Not Helpful 6 Helpful Not Helpful 5 Helpful What would cause my sub to kick in when radio is on and stop working when I change source to CD? The remote antenna power wire is responsible for the antenna coming out of a car with a retractable antenna. Remove the wire and find the correct remote amp, then turn on wire or ignition wire to the vehicle.
Not Helpful 15 Helpful You should be able to connect it to the auxiliary on the back of the stereo unit. Not Helpful 3 Helpful 7. My amp is already installed and I just bought a new sub. How do I connect my new sub to my old amp? There should be RCA female plugs on your amp, and on the new sub-box enclosure, there should be another set of RCA plugs or clamps.
Just match the positive and negatives. Not Helpful 14 Helpful Remote; connect the REM wire to a fuse that only has power when the car is on.
How to Install an Amp Without RCA Jacks | It Still Works
I cannot turn it up any higher than halfway without my amp going into protective mode. What would cause this? This could be caused by a bad ground. Run yourself a good wire for ground directly to the chassis. Not Helpful 1 Helpful 3. What if I bought my radio harness to fit my truck only? Will the wires still match up on the aftermarket radio I purchased? It will just plug into your truck and then connect color coordinated wires. Not Helpful 0 Helpful 1.
How should I connect the remote wire so that I don't have to disconnect it when I turn off the car? Hook it to a fuse connected to ignition turn on, like your accessory power fuse. Not Helpful 16 Helpful What do I do if my amp comes on with static through my speakers when I turn on the key, but nothing else comes through?
TVs & Home Theaters forum
Answer this question Flag as Where do you get lock nuts for the power and ground wires on my amp? Can I run 4 speakers and a subwoofer from a single amplifier?
- r6 matchmaking issues.
- How do you connect a subwoofer to an amplifier?.
- Hook up amp without rca jacks – Irish in the American Civil War.
- Subwoofer wire dilema - Forums - CNET.
Can I hook up a loc to the rear speaker wires if there is a factory amp to them? If not, where do I hook up the loc wires? Can you add subs to a factory radio? If so short simple easy way?
- How do you hook up an amp using a head unit without rca outputs?.
- guy im dating wants me to meet his friends;
- online dating south lanarkshire;
- Video of the Day.
- Popular Forums.
- Register Now.
- Trouble Logging In or Staying Logged In?.
And how can you test your subs to see if there working. Include your email address to get a message when this question is answered. Already answered Not a question Bad question Other. Tips Don't forget to test your rem wire before you assume it works. Last thing you need is a dead battery.
If your amp doesn't turn on, check the amp fuses. When connecting a line out connector to a factory head unit, it is advisable to use both sets of speaker wires to maintain the left and right stereo effect from modern music. Always remember to shut off the amp if you do so manually Soldering 12v power and ground connectors to the wires will reduce circuit resistance and make your power cleaner, giving you better sound.
Make sure that you use cables with the correct resistance or impedance for your setup. A bridged amp runs at a different impedance than the same amp in unabridged mode.
How to hook up an amp and sub to a stock stereo.
Getting this wrong may well overheat cables or even blow the amp itself so make sure your cables and setup are matched. Common values are 2, 4, or 8 ohms, so do your homework beforehand.
Warnings Always Disconnect the Negative terminal from your battery before doing anything with electricity on your car. Always be careful with electricity. Things You'll Need Stereo. Article Info wikiHow is a wiki similar to Wikipedia, which means that many of our articles are written collaboratively.
Car Audio Defined By A Chick
Loudspeakers In other languages: If your subwoofer doesn't have an internal amplifier , you'll definitely want to connect an amplifier to it. To do this, you'll need your subwoofer, an amplifier, at least one set of RCA cables these are the red, white, and yellow jacks on a single cable , speakers , and speaker wires.
First, you'll want to think about where you'll keep the subwoofer. Because the subwoofer is working mostly on the bass the low tones , it doesn't require as much directional pushing as speakers do.
- ct dating events!
- hook up new year.
- Report Abuse!
- hookah hookup burlington nc?
- online dating smiley faces?
Since you'll have to run cables and wires between the subwoofer and other devices, you might want to keep it just a few feet from your screen. To get started with the actual hook-up, you'll connect the subwoofer to the amplifier using the RCA cable. If you want a stereo hook-up, you'll need two sets of RCA cables. Connect the subwoofer output to the amplifier input. The jack on the amplifier may even be labeled "subwoofer output," just to make things easy for you.